Five Killer Quora Answers On Boarding Up A Door

관련링크

본문

How to Go About Boarding Up a Door

boarding up houses up a door is one method of protecting vacant investment properties from the elements. While it may not be able to prevent all damage, it can reduce certain problems caused by severe storms.

The idea of boarding up door up doors and windows can also deter trespassers, vandals, and squatters. Installing plywood boards over openings can be costly and time-consuming.

Measure the Door

The first thing you'll require is an accurate tape measure. You may also want to keep a ladder or chair handy for when you need to see more clearly at the top of the frame. Wear gloves and goggles if you have to make use of these tools.

Once you have the measuring instrument, start by taking the door width measurement. You can do this by running a tape measure horizontally along the door. Make sure to remove any extra parts of the door, like the sweep, when measuring. Then, take the height measurement by measuring up from the floor to the sill plate or the lintel. It is crucial to take measurements in multiple locations, particularly when measuring doors older than they might not be a perfect rectangular shape. If the measurements are different then use the largest number.

After you've recorded the width and height measurements then you'll have to figure out what size emergency boarding up near me you need for the frame. Ideally, it should be 2 inches greater than the door's width and 1 inch thicker than the door. 2'' higher. This will allow you enough room to shim both the door and frame to fit.

When you're ready to take the door frame's width and height measurements It's recommended to remove any trim or casing the door jambs, so you can see the studs that are behind them. This will help you determine the exact measurement of the gap between the studs and the frame.

After you've removed your trim, you'll be able to determine the dimensions of the door frame by running the tape measure across the entire frame in three locations and using the smallest measurement to determine your door's width. It is also important to measure the frame's height from top to bottom on both sides. Choose the shortest measurement for the width of your door.

If you're having issues with the measurements, get a professional to your house and conduct the measurements. They'll be able tell you exactly what kind of door and size you need and how to prepare the frame to accommodate the door you want to buy.

Plywood can be cut into pieces

A door frame is typically comprised of studs or boards that create an open space around the door. Two hinges are connected to the studs and keep a typical door in its place. If you want to refinish a door, you will need to remove it from its hinges over night. To keep insects out of your home and to secure the door's opening, a straightforward method to board the door is to put plywood in the opening. This is easy to do without the need to nail or screw the plywood to the frame of the door.

Plywood is affordable, simple to work with and looks great when it is finished. It is the ideal material to make a temporary solution for a problem where you have to take down an existing door to refinish it or put in an entirely new one. It is also a great option to secure the opening of an area that is being renovated, like an unfinished basement or construction site.

Start by measuring the width of the door opening and its height. Note the measurements on the plywood with a utility knife and an drywall square or any other metal straight edge. Then, you can snap a chalkline across each line to mark the area to cut. Then utilize a circular saw to cut out the plywood to size.

When cutting the plywood it is crucial to shield your eyes and ears. If you can, wear a pair of protective goggles and earplugs while working. It is also important to use a blade with lots of teeth that will allow you to cut quickly and without any tear-out. To avoid cutting pieces of wood from the edges of the cut using a small piece of wood as an example to guide the blade and hold it just a hair's width away from the mark when cutting.

A good way to keep the plywood in place without screwing it to the studs is by fixing two braces at each end. Set one brace on the inside and the other on the outside of the door. Place a 1-1/2-inch deck screw in each hole and then tighten with an open-end ratchet.

Fix the Plywood

It's now time to connect the frame to the panel once you have the plywood sheet cut to the proper size and the holes for rails and stiles of the door frame predrilled. This is a simple task that doesn't require any advanced carpentry skills if you have the right tools and follow the correct steps.

Set up a table near the doorway, with two sawhorses at each end, and framing lumber 2x4s. Utilize the marks you made during the measurement procedure to guide you in cutting the plywood. Mark the lines using the help of a utility knife, a drywall square or other metal straight edge. This will serve as a guide to the saw blade, and will prevent splintering of the plywood when you cut it.

Put on eye protection and cut along the scored lines using a circular saw or table saw fitted with a fine-tooth blade. Sand the edges of the panels with 120-grit paper to smooth it out and eliminate any burrs. After sanding apply a wood sealer and let it dry in accordance with the manufacturer's guidelines.

Install the hinges onto the door frame. If you're using a T-hinge make holes in the exterior face of your door for the straps of the hinges. Then, attach the hinge's outside edge to the frame with a screwdriver. Repeat the process on the inside of the door for the hinges remaining, being careful not to overtighten any of them or the hinge could shift.

If you're using a single outside T-hinged door, you can make it easier to lock and boarding up a door close with a chain latch by putting a piece wire through the loops on the outside hinges. Bend a small piece of tie wire in half, and place it through the two holes on the exterior of the door. Then connect the wires to tighten them and lock the door.

Install the Plywood

Using the measurements you took, place the plywood in the door opening. Move the header of the frame (top) and the sill. Use a level to make sure that there is no slop between the header and sill. If the level isn't quite right, place another shim where it is needed and continue the process until the sill and the header are even.

Once the plywood is in place, secure it using the stainless-steel hinge bolts and wingnuts. Use a screwgun equipped with an attachment for a hex head to avoid stripping off the heads of the screws.

If your home has studs running the length of your doorway, you can drill hanger bolts into every framing piece. This is a lot easier than using a drywall cutting tool to make the hole.

After installing the plywood determine the width and height of the door opening. If necessary, cut the bottom of the plywood to match the size of the door frame and cut two pieces of 1-by-6 framing lumber as braces that are positioned across the upper and lower ends of your door. Cut along the lines drawn on your plywood using a circular blade fitted with teeth that are finely-toothed. Wear eye protection. Splinters can be removed from cuts by using a sanding device.

Once you've got the two braces in place, nail each one to the plywood with pairs of 2-inch finishing nails. When you're finished, counter sink the heads of all the nails. The braces should be sealed using a high-quality wood sealing product, like the wipe-on polyurethane made by Minwax.

If the door is still too big for the doorway, you can add some decorative molding to fill in the gap between the door and jamb or resize the opening. However, in most situations, it's more affordable and simpler to just choose a new door. This can also alleviate any problems you might have had with the door you originally purchased if it was damaged and could no fit for the opening.

Warning: Use of undefined constant php - assumed 'php' (this will throw an Error in a future version of PHP) in /home/comp_simple01/public_html/theme/company_simple/skin/board/common/view.skin.php on line 135